Symantec New 2026 250-587 Test Tutorial (Updated 303 Questions)
250-587 Exam Questions Dumps, Selling Symantec Products
NEW QUESTION # 153
After installing the Volume Manager, you need to configure the Volume manager for large number of servers. You also need to consider the capacity and performance in installed environment. You want to optimize the performance of mirrored volumes by applying default Volume Manager policy. Which policy will you apply to get performance of mirrored volumes?
- A. Apply the round robin policy
- B. Apply the select policy
- C. Apply the siteread policy
- D. Apply the prefer policy
Answer: B
NEW QUESTION # 154
Which interface provides single sign-on access for the purpose of administering Data Loss Prevention servers, managing policies, and remediating incidents?
- A. Symantec Protection Center
- B. Symantec Information Manager
- C. Symantec Messaging Gateway
- D. Symantec Data Insight
Answer: A
NEW QUESTION # 155
You have to recommend appropriate virtual storage configurations for use by specific classes of applications, based on the details of each application's I/O requirements. Your application generates large volumes of temporary dat a. The RAID configuration for temporary space should aim to maximize I/O throughput. You also need to ensure that there is no unnecessary space overhead. Which RAID layout should you use?
- A. RAID-1
- B. RAID-0
- C. RAID-5
- D. RAID-1+0
Answer: B
NEW QUESTION # 156
Which command will you run to get the full path name of the file, if you only have the inode number?
- A. vxquot
- B. vxlsino
- C. vxquota
- D. vxfsstat
Answer: B
NEW QUESTION # 157
You were working with Veritas Volume Manager and the Volume Manager failed due to disk failure. You are required to recover the Veritas Volume Manager Configuration. Identify the correct sequence of actions that you would perform in this situation.
1. Reinstall the operating system
2. Replace the failed disk
3. Recover the VxVM configuration
4. Add the Volume Manager Packages
5. Startup Hot-relocation 6. Clean up the system configuration
- A. 4,3,2,6,1,5
- B. 2,1,4,3,6,5
- C. 6,2,1,4,5,3
- D. 3,6,1,5,2,4
Answer: B
NEW QUESTION # 158
What is the correct configuration for BoxMonitor.Channels that will allow the server to start as a Network Monitor server?
- A. Packet Capture, Copy Rule
- B. Packet Capture, Span Port
- C. Packet Capture, Network Tap
- D. Packet Capture, Network Monitor
Answer: A
NEW QUESTION # 159
Which two components can perform a scan of a workstation? (Select two.)
- A. Discover Server
- B. Enforce Server
- C. Endpoint Server
- D. Network Prevent
- E. DLP Agent
Answer: A,E
NEW QUESTION # 160
You are responsible for managing Veritas Enterprise Administrator. You are in the process of creating a new disk group. You first initialize an unitialized disk and then create a new disk group using the disk you initialized. You want to ensure that this disk is mounted when you boot the system.
What should you do next?
- A. Add the disk to the disk group
- B. Verify the disk name in the Object Tree
- C. Mount the volume
- D. Create a new volume on the disk
Answer: D
NEW QUESTION # 161
After installing Veritas Volume Manager for your large number of volumes, you will configure the volumes as per your requirement. But you find the performance is very slow. You need to reconfigure the volumes to achieve significant improvement in performance when there are multiple I/O streams. What should you do?
- A. Use Mirroring and Striping
- B. Use Mirroring
- C. Use RAID-5
- D. Use Striping
Answer: B
NEW QUESTION # 162
You execute the qio_convertdbfiles command to convert the database files to use Quick I/O. The command results with an error that the database files are not on a VxFS file system. You need to convert the database files to use Quick I/O. What should you do?
- A. Set the database type to DB2.
- B. Run the qio_getdbfiles command to get the database files on the VxFS file system.
- C. Remove the files from the mkgio.dat file.
- D. Predefine the DB2 environment variable $DB2DATABASE.
Answer: C
NEW QUESTION # 163
You are administering Veritas Volume Manager on the UNIX platform, and you need to remove the volume using vxassist command. Given the following steps:
1. Remove the volume entry from the /etc/vfstab file.
2. Remove all references to the volume by application programs.
3. Stop all Activity by VxVM on the volume using vxvol stop command.
4. Unmount the volume, which is mounted as a file system.
What are the necessary sequential steps you need to follow before removing the volume?
- A. 4,2,1,3
- B. 3,1,4,2
- C. 1,4,3,2
- D. 2,4,3,1
Answer: B
NEW QUESTION # 164
You have installed Storage Foundation 5.0 Standard server with a number of hosts. You want to centrally monitor and manage the hosts. You also want to generate reports for the hosts and the storage resources that the hosts consume. What should you do?
- A. Upgrade Storage Foundation 5.0 Standard to Storage Foundation 5.0 Enterprise.
- B. Install Veritas Storage Foundation Management Host on Storage Foundation 5.0 server.
- C. Install the Veritas Quick I/O option on Storage Foundation 5.0 server.
- D. Install Veritas Storage Foundation Management Server on Storage Foundation 5.0 server.
Answer: D
NEW QUESTION # 165
What does the ACTIVE plex state indicate?
- A. The data in the plex is not synchronized with the data in the CLEAN plexes.
- B. The plex state does not define which plex has the active data, and which plex does not have the active data.
- C. The plex does not participate in any I/O when plex is offline, so the contents of plex become outdated if the volume is actively written.
- D. The volume is currently started, and the volume is able to perform I/O.
Answer: D
NEW QUESTION # 166
You have large number of mirrored volumes, and the resynchronization process on mirrored volumes will take lot of time. You want to address enable Dirty Region Logging (DRL) and find out the cause why it takes a long time for resynchronization. You want to check the status of DRL logging to see if it is already enabled. How will you accomplish this task?
- A. Use the vxprint command with the -F%drllogging $DRLVOL option
- B. Use the vxprint command with the -F%drllogging $DCOVOL option
- C. Use the vxprint command with the -F%dcologging $DCOVOL option
- D. Use the vxprint command with the -F%drllogging $$DCONAME option
Answer: D
NEW QUESTION # 167
You are working with the Storage Foundation Intelligent Storage Provisioning feature, to create a new mirrored volume. To prevent system failure, you want to ensure that you are able to perform a recovery of mirrored volumes in minimum response time. What should you do?
- A. Create a Snap object log.
- B. Create a RAID-5 log.
- C. Create a Dirty Region Log.
- D. Create a Data Change Map log.
Answer: C
NEW QUESTION # 168
You need to provide storage space for database application, including permanent data, temporary space, and activity log dat a. You need to ensure that the storage space that you provide offers data protection against disk failures. Which storage techniques will you use? (Each correct answer presents part of the solution. Select two.)
- A. Concatenated
- B. RAID-5
- C. RAID-1
- D. RAID-0
- E. RAID-1+0
Answer: B,C
NEW QUESTION # 169
You have installed site awareness licenses on all hosts in the remote mirror configuration. You want the volume to be automatically mirrored across sites when it is created and you specify the allsites=on attribute with the vxassist command. Which read policy do you need to set to accomplish this task?
- A. Prefer policy
- B. Round robin policy
- C. Siteread policy
- D. Select policy
Answer: C
NEW QUESTION # 170
Which option should be used to optimize the performance of a network share Discover scan?
- A. use an incremental scan to only include previously unscanned items
- B. ensure that the target file system is defragmented regularly
- C. configure credential prefetching to reduce delay in authentication
- D. disable antivirus scanning for network shares on the detection server
Answer: C
NEW QUESTION # 171
An administrator is applying a newly created agent configuration to an Endpoint server. Upon inspection, the new configuration is unassigned in the Endpoint Server Details. What is a possible cause for the new configuration failing to be assigned?
- A. the new agent configuration was saved without applying it to the Endpoint server
- B. the server that the new agent configuration was applied to needs to be recycled
- C. the new agent configuration was copied and modified from the default agent configuration
- D. the system default settings were saved to the new agent configuration
Answer: A
NEW QUESTION # 172
The VxVM operation fails while importing a disk group and you get an error message "VxVM vxdg ERROR V-5-1-2907 diskgroup: Disk group does not exist" How will you solve this problem?
- A. Export a disk group from the current host and import the disk group to another host.
- B. Export a disk group from another host.
- C. If the disk group already exists on the exported host, import it to the current host.
- D. Restore the configuration for the disk group from the backup.
Answer: C
NEW QUESTION # 173
You are the administrator of Veritas Volume Manager in Veritas Storage Foundation environment. You want to remove a disk from a disk group. You execute the command vxdg -g dg01rmdisk d001. After executing the command, you are prompted with the error "VxVM vxdg ERROR V-5- 552 disk diskname is used by one or more subdisks." You want to ensure you are able to remove the disk from the disk group. What should you do?
- A. Use -n option with vxdg command
- B. Use -o option with vxdg command
- C. Use -t option with vxdg command
- D. Use -k option with vxdg command
Answer: D
NEW QUESTION # 174
Refer to the exhibit.
An administrator needs to implement the use of a scanner, but is unfamiliar with the general, highlevel process associated with scanners. Which action occurs in step 3?
- A. the scanner process is started by a user or scheduled event
- B. the scanner connects to target and reads the content and metadata
- C. the scanner reviews and confirms configuration parameters
- D. the scanner packages filtered content and posts the data to Discover server
Answer: B
NEW QUESTION # 175
You are working on Storage foundation for DB2. You create a file system and you want to mount the file system to enable a Quick I/O. However, you are not able to mount the file system. What could be a probable cause? (Each correct answer presents part of the solution. Select two.)
- A. The mount point path is not an absolute path name.
- B. The Quick I/O is not licensed.
- C. The file system is read-only.
- D. You are not logged in as a root user.
Answer: A,D
NEW QUESTION # 176
You need to create a new volume. The new volume will only use disks on controller 1. You want to execute the vxassist command with the ctlr:c1 storage attribute. You want to ensure that the command provides desired output. What should you ensure to meet the required goal?
- A. Ensure that storage attribute is a part of the disk group.
- B. Ensure that storage attribute is a part of the volume.
- C. Ensure that storage attribute is a part of the disk.
- D. Ensure that storage attribute is a part of the plex.
Answer: A
NEW QUESTION # 177
......
250-587 Cert Guide PDF 100% Cover Real Exam Questions: https://examsforall.lead2passexam.com/Symantec/valid-250-587-exam-dumps.html